DG-10Y033D
Model No. Page
GW5DGA**M04
? Do not touch resin part including white resin part on the surface of LED.
No light emission may occur due to damage of resin or cutting wire of LEDs by outer force.
When using tweezers, please handle by ceramic substrate part and avoid touching resin part.
For mounting, please handle by side part of ceramic or the specified area shown below.
Handling area
⑤ Connecting method
In case of solder connecting method, follow the conditions mentioned below.
? Use Soldering iron with thermo controller (tip temperature 380 ℃ ), within 5 seconds per one place.
? Secure the solderwettability on whole solder pad and leads.
? During the soldering process, put the ceramic board on materials whose conductivity is poor enough
not to radiate heat of soldering.
? Warm up (with using a heated plate) the substrate is recommended before soldering.
( preheat condition: 100 ℃ ~ 150 ℃ , within 60 sec )
? Avoid touching a part of resin with soldering iron.
? This product is not designed for reflow and flow soldering.
? Avoid such lead arrangement as applying stress to solder-applied area.
? Please do not detach solder and make re-solder.
? Please solder evenly on each electrodes.
? Please prevent flux from touching to resin.
⑥ Static electricity
This product is subject to static electricity, so take measures to cope with it.
Install circuit protection device to drive circuit, if necessary.
⑦ Drive method
? Any reverse voltage cannot be applied to LEDs when they are in operation or not.
Design a circuit so that any flow of reverse or forward voltage can not be applied to LEDs
when they are out of operation.
? Module is composed of LEDs connected in both series and parallel.
Constant voltage power supply runs off more than specified current amount due to lowered V F
caused by temperature rise.
Constant current power supply is recommended to drive.
⑧ Cleaning
Avoid cleaning, since silicone resin is eroded by cleaning.
⑨ Color-tone variation
Chromaticity of this product is monitored by integrating sphere right after the operation.
Chromaticity varies depending on measuring method, light spread condition, or ambient temperature.
Please verify your actual conditions before use.
16 of 18
相关PDF资料
GW5DGA30M04 LED MOD 15WATT ZENIGATA 3025K
GW5DGA27M04 LED MOD 15WATT ZENIGATA 2700K
1-231666-2 HANDTOOL KIT MODULAR PLUG
GW5DMA30M04 LED MOD 15WATT ZENIGATA 3025K
1583662-1 HYDRAULIC HOSE ASSEMBLY 6 FT.
PGK-0060 NEMA 3 PANEL ADAPTER
GW5DMA27M04 LED MOD 15WATT ZENIGATA 2700K
P51-750-S-I-P-5V-000-000 SENSOR 750PSIS 7/16 UNF 5V
相关代理商/技术参数
GW5DGA50M04 功能描述:LED照明模块 15W Meg Zenigata 5000K 1250LM 90CRI RoHS:否 制造商:Cree, Inc. 产品:LED Modules LED 数量:1 照明颜色:Neutral White 射束角:96 deg 波长/色温:3500 K 光强度: 光通量:3000 lm 宽度: 长度:88.2 mm 系列: 封装:Bulk
GW5DGA65M04 功能描述:LED照明模块 15W Meg Zenigata 6500K 1250LM 90CRI RoHS:否 制造商:Cree, Inc. 产品:LED Modules LED 数量:1 照明颜色:Neutral White 射束角:96 deg 波长/色温:3500 K 光强度: 光通量:3000 lm 宽度: 长度:88.2 mm 系列: 封装:Bulk
GW5DGC27M04 功能描述:LED照明模块 25W Meg Zenigata 2700K 1910LM 93CRI RoHS:否 制造商:Cree, Inc. 产品:LED Modules LED 数量:1 照明颜色:Neutral White 射束角:96 deg 波长/色温:3500 K 光强度: 光通量:3000 lm 宽度: 长度:88.2 mm 系列: 封装:Bulk
GW5DGC30M04 功能描述:LED照明模块 25W Meg Zenigata 3000K 1950LM 93CRI RoHS:否 制造商:Cree, Inc. 产品:LED Modules LED 数量:1 照明颜色:Neutral White 射束角:96 deg 波长/色温:3500 K 光强度: 光通量:3000 lm 宽度: 长度:88.2 mm 系列: 封装:Bulk
GW5DGC30MR4 制造商:Sharp Microelectronics Corporation 功能描述:
GW5DGC35M04 功能描述:LED照明模块 25W Meg Zenigata 3500K 1970LM 93CRI RoHS:否 制造商:Cree, Inc. 产品:LED Modules LED 数量:1 照明颜色:Neutral White 射束角:96 deg 波长/色温:3500 K 光强度: 光通量:3000 lm 宽度: 长度:88.2 mm 系列: 封装:Bulk
GW5DGC40M04 功能描述:LED照明模块 25W Meg Zenigata 4000K 2050LM 92CRI RoHS:否 制造商:Cree, Inc. 产品:LED Modules LED 数量:1 照明颜色:Neutral White 射束角:96 deg 波长/色温:3500 K 光强度: 光通量:3000 lm 宽度: 长度:88.2 mm 系列: 封装:Bulk
GW5DGC50M04 功能描述:LED照明模块 25W Meg Zenigata 5000K 2080LM 90CRI RoHS:否 制造商:Cree, Inc. 产品:LED Modules LED 数量:1 照明颜色:Neutral White 射束角:96 deg 波长/色温:3500 K 光强度: 光通量:3000 lm 宽度: 长度:88.2 mm 系列: 封装:Bulk